Results 1 to 9 of 9

Thread: No spark

  1. #1
    Join Date
    Oct 2024
    Location
    Canada
    Posts
    6

    Default No spark

    I just received this 56 mark II. It has sat for many years. It turns over. I cleaned out the fuel tank, added new gas. Fuel pump works but I get no spark at the plugs. Coil was bad so it was replaced with no luck. Plugs were cleaned and gapped. Still nothing. Any ideas??

  2. #2
    Join Date
    Jul 2009
    Location
    Farmington Hills, MI
    Posts
    4,712

    Default

    Is the car getting gas through the carb? You can quickly tell if it's a fuel delivery problem by using a syringe of squeeze bottle to fill the carb bowl through the vent holes. If it starts it's the carb. Is it getting 9 volts at the coil with the ignition switch on? if it gets no voltage with the ignition switch on the resistor is bad. Does it get 12 volts while cranking? You're likely going to do it anyway, but adding a Pertronix ignition makes points problems disappear and makes the car quite reliable.

    Take the cap off and see if the rotor is turning. See of the points are stuck open.

    Buy a Service Manual and an Authenticity Manual. Most questions are covered.
    Barry Wolk
    Farmington Hills, MI

    C5681126

  3. #3
    Join Date
    Jun 2011
    Location
    Phoenix Az
    Posts
    447

    Default

    Check for voltage at the ballast resistor. It needs to have voltage at both sides to send voltage to the coil. After this check or replace your points and condenser in the distributor.
    Last edited by Milsteads Garage; 10-20-2024 at 11:52 AM.
    Morgan Milstead
    C5691157

  4. #4
    Join Date
    Oct 2024
    Location
    Canada
    Posts
    6

    Default

    Checked rotor, it turns, had power at both resistor terminals, new coil, but still nothing. Points and condensor look good, but i guess i could change them .

  5. #5
    Join Date
    Oct 2011
    Location
    Yellow Springs, OH
    Posts
    2,798

    Default

    Do you have spark from the coil to the distributor?
    If so, replace all of it: distributor cap, rotor, points, and condenser. If not, is there a kill switch? Maybe an extra wire on the coil grounding it out?
    Last edited by jdsnoddy; 10-20-2024 at 05:43 PM.
    John Snoddy

  6. #6
    Join Date
    Oct 2024
    Location
    Canada
    Posts
    6

    Default

    No extra wire grounding the coil. I will replace all of it. This week. Thanks. I will keep you posted.

  7. #7
    Join Date
    Nov 2009
    Location
    Switzerland
    Posts
    2,240

    Default

    It can be just oil or dirt between the points. Clean them with a piece of cardboard, it makes wonders! I had the phenomen three times: on my '56 Cadillac et twice on the Corvette from a friend. You can also check the voltage at the coil's output: if the point are closed, you should have 0 Volt.
    Check also the internal wire doing to the points: with the age, it can deteriore and no more doing its job.
    Roger

  8. #8
    Join Date
    Oct 2011
    Location
    Yellow Springs, OH
    Posts
    2,798

    Default

    I would also suggest, after you get spark, to fill the carburetor bowl with 6 ounces of 2 cycle gasoline.
    A little prime is a good thing.
    John Snoddy

  9. #9
    Join Date
    Oct 2024
    Location
    Canada
    Posts
    6

    Default

    I have fantastic news. The Conti is up and running strong. I put a new coil in, points were cleaned, and cleaned distributor cap. Motor is strong. Thank you all for advice. I appreciate it. Now going to get a safety so I can get driving. ��
    Alex Wolf
    Canada

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •